Golf Cart Battery Wiring: 36V and 48V Diagrams, Series vs Parallel

October 12, 2026Nick’s Golf Carts
Golf Cart Battery Wiring: 36V and 48V Diagrams, Series vs Parallel

Golf Cart Batteries · Wiring

Almost every golf cart wires its batteries in series. Positive goes to negative, battery to battery, until the voltages add up to the pack: six 6V batteries for 36V, or six 8V, eight 6V or four 12V batteries for 48V.

Key Takeaways

  • 01

    Golf cart packs are wired in series, so voltages add up and the amp-hour rating stays the same as one battery.

  • 02

    A 36V cart uses six 6V batteries. A 48V cart uses six 8V, eight 6V or four 12V batteries.

  • 03

    Take the main negative cable off first and put it back on last. That one habit prevents most sparks.

  • 04

    Tighten terminals to the battery maker’s torque spec. Loose and over-tight connections both cause heat and damage.

  • 05

    A single battery wired backwards drops the whole pack by twice that battery’s voltage, and a reversed pack can ruin a controller.

How Golf Cart Batteries Are Wired: The Short Answer

Golf cart batteries are wired in series. A short cable called a jumper runs from the positive post of one battery to the negative post of the next, all the way down the row. One loose negative post at the start of the string and one loose positive post at the end become the pack’s main negative and main positive. Those two cables feed the cart. Six 6V batteries make 36V. Six 8V, eight 6V or four 12V batteries make 48V.

That is the whole idea. The rest of this guide shows each layout in plain text, tells you how to figure out which pack you have, and covers the details that matter when you actually put a wrench on a terminal: the order of the cables, the right torque, the cable size and the safety steps that keep you and your cart in one piece.

Series vs Parallel: Why Carts Almost Always Use Series

There are two basic ways to join batteries. In series, you connect positive to negative. The voltages add up and the capacity stays the same. In parallel, you connect positive to positive and negative to negative. The voltage stays the same and the capacity adds up.

A golf cart motor needs high voltage, not a 6V or 12V supply with a huge capacity. Higher voltage means less current for the same power, which means thinner cables, less heat and a more efficient motor. That is why the factory wires the pack in series. You will almost never see a stock cart with batteries in parallel.

If you want to run 12V accessories like lights or a stereo, the clean way is a voltage reducer wired across the full pack. Tapping one or two batteries in the string for 12V drains those batteries faster than the rest. Over a season that unbalances the pack and shortens its life. If you want a refresher on battery types and how many your cart needs, start with our golf cart battery pack basics before you pick up a wrench.

What Series Wiring Does to Voltage and Amp-Hours

Here is the math that confuses most people. When batteries are in series, the voltage adds up but the amp-hours do not. Six 6V batteries rated at 225 amp-hours give you a 36V pack rated at 225 amp-hours, not 1,350. The energy does add up, though. Multiply volts by amp-hours and you get watt-hours: 36V times 225Ah is about 8.1 kilowatt-hours.

That is why comparing packs by amp-hours alone can mislead you. A 48V pack of six 8V batteries at 170Ah stores about 8.2 kWh. A 48V pack of eight 6V batteries at 225Ah stores about 10.8 kWh. Same voltage, very different range. The worked examples below use typical ratings so you can see the difference.

Common golf cart battery packs and what they store

PackBatteriesExample rating eachPack voltagePack amp-hoursApprox. energy
36VSix 6V225Ah36V225Ah8.1 kWh
48VSix 8V170Ah48V170Ah8.2 kWh
48VEight 6V225Ah48V225Ah10.8 kWh
48VFour 12V150Ah48V150Ah7.2 kWh

36V Wiring: Six 6V Batteries, Step by Step

Older carts and many fleet carts run 36 volts from six 6V batteries. The batteries sit in one or two rows under the seat. Number them 1 to 6 in the order the jumpers run, not by where they sit in the tray. Battery 1 holds the main negative cable. Battery 6 holds the main positive cable. Here is the layout written out as a text diagram.

36V pack: six 6V batteries in series

text
MAIN NEGATIVE (to cart)  ->  B1 (-)
B1 (+)  ->  jumper  ->  B2 (-)
B2 (+)  ->  jumper  ->  B3 (-)
B3 (+)  ->  jumper  ->  B4 (-)
B4 (+)  ->  jumper  ->  B5 (-)
B5 (+)  ->  jumper  ->  B6 (-)
B6 (+)  ->  MAIN POSITIVE (to cart)

5 jumpers + 2 main cables
6 x 6V = 36V

Count the cables before you start. A 36V pack has five jumpers and two main cables. If you count six jumpers, something is wired in a loop. If you count four, one battery is missing from the string. A quick count catches most wiring mistakes before they cost you anything.

48V Wiring: Six 8V, Eight 6V or Four 12V

Most current electric carts run 48 volts. The rule is the same as 36V: positive to negative down the line, one main negative at the start and one main positive at the end. Only the number of batteries changes. The text diagrams below show each version.

48V pack: six 8V batteries in series

text
MAIN NEGATIVE  ->  B1 (-)
B1 (+) -> B2 (-)
B2 (+) -> B3 (-)
B3 (+) -> B4 (-)
B4 (+) -> B5 (-)
B5 (+) -> B6 (-)
B6 (+)  ->  MAIN POSITIVE

5 jumpers + 2 main cables
6 x 8V = 48V

48V pack: eight 6V batteries in series

text
MAIN NEGATIVE  ->  B1 (-)
B1 (+) -> B2 (-)
B2 (+) -> B3 (-)
B3 (+) -> B4 (-)
B4 (+) -> B5 (-)
B5 (+) -> B6 (-)
B6 (+) -> B7 (-)
B7 (+) -> B8 (-)
B8 (+)  ->  MAIN POSITIVE

7 jumpers + 2 main cables
8 x 6V = 48V

48V pack: four 12V batteries in series

text
MAIN NEGATIVE  ->  B1 (-)
B1 (+) -> B2 (-)
B2 (+) -> B3 (-)
B3 (+) -> B4 (-)
B4 (+)  ->  MAIN POSITIVE

3 jumpers + 2 main cables
4 x 12V = 48V

Which 48V Configuration Your Cart Has

You do not need a manual to work this out. Lift the seat and count the batteries, then read the voltage printed on any one of them. Six batteries on a 48V cart means 8V batteries. Eight batteries means 6V. Four means 12V. If the labels are worn, count the caps on top of a flooded battery: each cell is about 2 volts, so three caps is a 6V battery, four caps is 8V and six caps is 12V.

Stick with the configuration the cart came with when you replace a pack. Swapping six 8V batteries for eight 6V can add range, but only if the tray, hold-downs and cables fit the extra batteries safely. Never mix old and new batteries in one string, and never mix sizes. The weakest battery sets the limit for the whole pack and gets worked the hardest.

Reading the Diagram: Main Positive, Main Negative and the Jumpers

Main negative
The cable from the first battery’s negative post to the cart’s negative lead. It comes off first and goes on last.
Main positive
The cable from the last battery’s positive post to the cart. On many carts it runs through the solenoid, the heavy switch that connects the pack to the motor circuit when you press the pedal.
Jumpers
The short cables between batteries. Each one joins a positive post to the next battery’s negative post.
Pack voltage check
Meter across the main negative post and main positive post. A fully charged lead-acid 48V pack at rest reads about 50 to 51 volts; a 36V pack reads about 38 volts.
Single battery check
A fully charged 6V battery at rest reads about 6.3 to 6.4 volts, an 8V about 8.4 to 8.5 volts, and a 12V about 12.7 volts.

If the cart clicks but will not move after a battery job, the problem is often not the batteries at all. A loose main cable or a weak solenoid gives the same symptom. Our step-by-step guide on how to test the solenoid walks you through ruling it out with a basic multimeter.

How to Hook Up Golf Cart Batteries: Step by Step

STEP 01Put the cart in a safe state

Park on level ground, set the brake, turn the key off and put the direction switch in neutral. If your cart has a Run/Tow switch, set it to Tow. Take off rings, watches and metal bracelets.

Put on safety glasses and gloves. Work in a ventilated space, away from flames and sparks.

STEP 02Photograph and label everything
Take two clear photos of the battery bay from above before you touch a cable. Put a piece of tape on each main cable and mark it. These photos are your real wiring diagram, because they show exactly how your cart’s tray is laid out.
STEP 03Remove the main negative first
Loosen and lift off the main negative cable from battery 1. Tuck it away so it cannot swing back onto a post. Then remove the main positive, then the jumpers. With the main negative off, a slipped wrench has no complete circuit to arc through.
STEP 04Clean posts and set the new batteries
Clean the cable ends with a terminal brush. Set each new battery in the tray with the posts facing the same way as in your photos. Secure the hold-downs so nothing can slide when the cart hits a bump.
STEP 05Install the jumpers
Connect each jumper from one battery’s positive post to the next battery’s negative post. Work down the string in order. Snug each nut by hand first, then torque it to the battery maker’s spec.
STEP 06Connect the main positive, then the main negative last
Fit the main positive to the last battery. The main negative goes on battery 1 last of all. A small spark at that final connection is normal on many carts because the controller has capacitors that charge up.
STEP 07Verify with a meter
Meter across the main posts and confirm the reading matches the pack voltage. Then check each battery on its own. Every reading should be close to the others. Switch back to Run, turn the key on and test drive slowly.

Cable Size, Terminal Torque and the Mistakes That Cost a Controller

Torque matters more than most owners think. Trojan, one of the largest deep-cycle battery makers, lists terminal torque values in Trojan Battery’s published user guides. For its common 5/16-inch bolt terminals on golf cart batteries, the spec is 95 to 105 inch-pounds, about 11 to 12 newton-meters. The guide warns that over-tightening can break a terminal, and that loose connections can lead to meltdown or fire. Use an inch-pound torque wrench, not a long breaker bar. Always check the guide for your exact battery and terminal type, because values change by design.

Cable size is the other half of a good connection. Most factory carts use 6-gauge jumpers. Carts with a high-amp upgraded controller often move to 4-gauge or 2-gauge cables so the wiring does not become the bottleneck. The lower the gauge number, the thicker the cable. Thicker cables run cooler and lose less voltage. If you are upgrading power, read up on controller symptoms and upgrade costs first, since cable size should match what the controller pulls.

01 · Mistake

One battery wired backwards

In series, a reversed battery subtracts instead of adds. A six-by-8V pack with one battery flipped reads about 32 volts instead of 48, because that battery takes away twice its voltage. The cart may crawl or not move at all, and the reversed battery can be damaged by charging.

02 · Mistake

Whole pack reversed at the main cables

Swap the main positive and main negative and you send reverse polarity into the cart. Depending on the model, that can blow a fuse, damage the charger port circuit or destroy the controller. Check twice before the last connection.

03 · Mistake

Washers or lugs stacked in the wrong order

The cable lug should sit flat against the post or terminal, with the washer and nut on top. A washer trapped between the lug and the post adds resistance. That spot heats up under load and melts posts over time.

04 · Mistake

Mixing old and new batteries

A new battery in a tired string gets pulled down to the level of the old ones. Replace the whole pack together, and use batteries of the same make, model and age.

05 · Mistake

Tools left on top of the batteries

A wrench laid across two posts creates a dead short. It can weld itself in place, heat red hot and crack a battery case in seconds.

Safety First: What the Rules Say

Lead-acid batteries give off hydrogen gas while charging, and they hold sulfuric acid. The workplace rules in OSHA’s standard 1910.178 on battery charging were written for industrial truck batteries, but the hazards are the same in your garage. The standard calls for adequate ventilation to clear fumes from gassing batteries, facilities for flushing and neutralizing spilled electrolyte, no smoking in charging areas, steps to prevent open flames, sparks or electric arcs, and keeping tools and other metal objects away from the tops of uncovered batteries.

At home, that means a few simple habits. Charge with the garage door open. Keep water and baking soda nearby for spills. Wear eye protection whenever you open caps or work on terminals. Use insulated tools, or wrap the handle of a standard wrench in electrical tape. Never lean over a battery while making the final connection. If you top up flooded batteries often, a single-point battery watering system cuts down on how often you open caps over the pack.

Lithium Changes the Wiring: What's Different in a 48V or 51.2V Pack

A lithium pack is a different animal. Most lithium golf cart batteries are a single case that replaces the whole lead-acid string. Inside, the series wiring is already done. A common 51.2V lithium iron phosphate (LiFePO4) pack is 16 cells at 3.2 volts each, joined in series by the maker. You connect just one main positive and one main negative.

The pack also has a battery management system, or BMS. That is a small circuit board that watches each cell, balances them and shuts the pack off if it gets too hot, too cold or too low. Lithium needs a charger with a lithium profile, because a lead-acid charger can overcharge it or fail to charge it at all. Some lithium kits also add a state-of-charge display and a voltage reducer for accessories. If you are weighing the switch, our breakdown of lithium battery conversion cost covers what a full installed kit runs and what comes in the box.

Tools, Time and When to Let the Service Department Do It

For a straight swap of a lead-acid pack, plan on an afternoon. You will want a socket set, an inch-pound torque wrench, a terminal brush, a digital multimeter, safety glasses, gloves and a way to lift heavy batteries. A single 8V golf cart battery weighs around 60 pounds, so a full pack is several hundred pounds of lifting. Take your time, keep your back straight and get help.

Some jobs are better handed to a pro. Call in help if your cables are corroded through, if posts are melted, if the cart has an aftermarket controller or wiring you did not install, or if you are converting to lithium. A shop can also load-test the old pack before you buy a new one, since a single dead battery is sometimes the whole problem. The service department at Nick’s Golf Cars can take a look, and you can reach the team at 1-800-552-0606.

QHow many batteries does a golf cart take?
Most electric golf carts take four, six or eight batteries. A 36V cart uses six 6V batteries. A 48V cart uses six 8V, eight 6V or four 12V batteries. A lithium cart usually has one pack that replaces the whole string.
QAre golf cart batteries wired in series or parallel?
Series. Each battery’s positive post connects to the next battery’s negative post, so the voltages add up to 36V or 48V. Parallel wiring keeps the voltage low, which is why stock carts do not use it for the drive pack.
QHow do you wire six 8-volt batteries for 48 volts?
Number the batteries 1 to 6. Connect battery 1’s positive to battery 2’s negative, then 2 to 3, and so on to battery 6. That uses five jumpers. The main negative cable goes on battery 1’s negative post and the main positive goes on battery 6’s positive post. Six times 8V gives you 48V.
QWhat size cable do golf cart batteries need?
Most factory carts use 6-gauge jumper cables. Carts with high-amp upgraded controllers often use 4-gauge or 2-gauge cables so the wiring can handle the extra current without heating up. Match the cable size to what your controller pulls.
QWhat happens if you wire a golf cart battery backwards?
One reversed battery in a series pack lowers the total voltage by twice that battery’s rating, so a 48V pack can read about 32V. Reversing the whole pack at the main cables can blow a fuse or damage the controller and charger circuits. Always meter the pack before you drive.
QHow do you hook up golf cart batteries after replacing them?
Follow your before photos. Install all the jumpers positive to negative first, then the main positive, and connect the main negative last. Torque every terminal to the battery maker’s spec, then check pack voltage with a meter before switching the cart back to Run.
QDoes a lithium pack use the same wiring?
Not usually. Most lithium golf cart batteries are one pack with the cells already wired in series inside, plus a battery management system. You connect one main positive and one main negative, and you need a charger with a lithium profile.

Rather not wire it yourself?

Have a pro handle your battery pack

Corroded cables, melted posts or a lithium upgrade on the way? Reach out to Nick’s Golf Cars and talk to the service team about your cart.

Nick’s Golf Carts

Ready to find your cart?

Shop live inventory across five showrooms, or talk to a specialist.